StrataGemma PS 197A
DESCRIPTION
This new generation of 100% polymer spray coating technology offers a fast cure and provides a seamless coating for waterproofing applications. StrataGemma PS 197A is a volatile-free system that results in a high strength coating. It can be applied to a thickness of 1-5 mm in a single application.
TECHNICAL PROPERTIES
| Technical Parameters | StrataGemma PS 197A | Unit | Standard |
| Color | White | – | – |
| Gel Time | 4 | Seconds | – |
| Tack Free Time | 6 | Seconds | – |
| Hardness | 45 | Shore D | DIN 53505 |
| Tensile | 24.2 | MPa | DIN 53504 |
| Elongation | 390 | % | DIN 53504 |
| Tear Strength | 73.9 | N/mm | DIN 53515 |
LIQUID CHARACTERISTICS
| Characteristics | Reactor 2054 | Characteristics | StrataGemma PS 197A |
| Viscosity @ 25℃ | 775 mPa.s | Viscosity @ 25℃ | 350 mPa.s |
| Specific Gravity @ 25℃ | 1.11 g/ml | Specific Gravity @ 25℃ | 1.05 g/ml |
PROCESSING PARAMETERS
| Volume Mix Ratio | 1:1 |
| Processing Temperature | Min. 80℃ |
| Pressure | Min. 180 bar |
NOTE: StrataGemma PS 197A blend needs to be stirred well prior to use.
SUBSTRATE PREPARATIONS GENERAL RECOMMENDATIONS
Spray systems should only be applied to clean, dry and sound surfaces. Remove all dust, oil, grease, and lose rust, or any other foreign material to ensure adequate adhesion.
CONCRETE
Concrete substrates should be completely cured before coating or a minimum of 28 days must have passed. Laitance, release agents, and salts need to be removed by high-pressure water jetting or sandblasting. Other substrate cleaning guidelines can be consulted via SSPC-SP13, NACE 6. It is important to note that the use of a primer is generally needed to achieve adequate adhesion. The recoat window recommended by your supplier should also be respected.
METAL/STEEL
Metal surfaces need to be prepared by means of sandblasting until they have a nearly white appearance. The surface profile will ensure adequate mechanical adhesion. Solvent cleaning is needed to remove any oil and grease. If priming is needed, this should be undertaken within eight hours of sandblasting to prevent any flash rusting.
STORAGE
Containers of StrataGemma PS 197A should be stored indoors in a well-ventilated area under normal factory conditions at temperatures of between 20-25°C. Stored under recommended conditions, and in an unopened, sealed container.
SHELF-LIFE
StrataGemma PS 197A has a storage life of six months.
TECHNICAL SERVICE
GCPL has an advisory service on concrete mix design & application of the right products at the right place, can be contacted if assistance is
- GCPL maintains a technical division with highly qualified Technical Personnel to investigate and advise on subjects related to concrete and the Construction
- The Division will advise on the correct use and selection of the right products at the right
StrataGemma PS 197B
DESCRIPTION
This new generation hybrid spray coating technology offers a fast cure and provides a seamless coating for waterproofing applications. StrataGemma PS 197B is a volatile-free system that results in a high strength coating. It can be applied to a thickness of 1-5 mm in a single application.
TECHNICAL PROPERTIES
| Technical Parameters | StrataGemma PS 197B | Unit | Standard |
| Color | Natural* | – | – |
| Gel Time | 3 | Seconds | – |
| Tack Free Time | 4 | Seconds | – |
| Hardness | 45 | Shore D | DIN 53505 |
| Tensile | 22.9 | MPa | DIN 53504 |
| Elongation | 350 | % | DIN 53504 |
| Tear Strength | 68.7 | N/mm | DIN 53515 |
- Also available in Black and Red
LIQUID CHARACTERISTICS
| Characteristics | Reactor 2054 | Characteristics | StrataGemma PS 197B |
| Viscosity @ 25℃ | 775 mPa.s | Viscosity @ 25℃ | 1170 mPa.s |
| Specific Gravity @ 25℃ | 1.11 g/ml | Specific Gravity @ 25℃ | 1.0 g/ml |
PROCESSING PARAMETERS
| Volume Mix Ratio | 1:1 |
| Processing Temperature | Min. 65℃ |
| Pressure | Min. 160 bar |
NOTE: StrataGemma PS 197B blend needs to be stirred well prior to use.
SUBSTRATE PREPARATIONS GENERAL RECOMMENDATIONS
Spray systems should only be applied to clean, dry and sound surfaces. Remove all dust, oil, grease, and lose rust or any other foreign material to ensure adequate adhesion.
CONCRETE
Concrete substrates should be completely cured before coating or a minimum of 28 days must have passed. Laitance, release agents, and salts need to be removed by high-pressure water jetting or sandblasting. Other substrate cleaning guidelines can be consulted via SSPC-SP13, NACE 6. It is important to note that the use of a primer is generally needed to achieve adequate adhesion. The recoat window recommended by your supplier should also be respected.
METAL/STEEL
Metal surfaces need to be prepared by means of sandblasting until they have a nearly white appearance. The surface profile will ensure adequate mechanical adhesion. Solvent cleaning is needed to remove any oil and grease. If priming is needed, this should be undertaken within eight hours of sandblasting to prevent any flash rusting.
STORAGE
Containers of StrataGemma PS 197B should be stored indoors in a well-ventilated area under normal factory conditions at temperatures of between 20-25°C. Stored under recommended conditions, and in an unopened, sealed container.
SHELF-LIFE
StrataGemma PS 197B has a storage life of six months.
TECHNICAL SERVICE
GCPL has an advisory service on concrete mix design & application of the right products at the right place, can be contacted if assistance is
- GCPL maintains a technical division with highly qualified Technical Personnel to investigate and advise on subjects related to concrete and the Construction
- The Division will advise on the correct use and selection of the right products at the right
StrataGemma PS 197C
DESCRIPTION
This new generation of 100% polymer spray coating technology offers a fast cure and provides a seamless coating for waterproofing applications. StrataGemma PS 197C is a volatile-free system that results in a high strength coating. It can be applied to a thickness of 1-5 mm in a single application.
TECHNICAL PROPERTIES
| Technical Parameters | StrataGemma PS 197C | Unit | Standard |
| Color | White* | – | – |
| Gel Time | 8 | Seconds | – |
| Tack Free Time | 13 | Seconds | – |
| Hardness | 60 | Shore D | DIN 53505 |
| Tensile | 21.3 | MPa | DIN 53504 |
| Elongation | 190 | % | DIN 53504 |
| Tear Strength | 100.9 | N/mm | DIN 53515 |
- Also available in Grey
LIQUID CHARACTERISTICS
| Characteristics | Reactor 2054 | Characteristics | StrataGemma PS 197C |
| Viscosity @ 25℃ | 610 mPa.s | Viscosity @ 25℃ | 150 mPa.s |
| Specific Gravity @ 25℃ | 1.14 g/ml | Specific Gravity @ 25℃ | 1.04 g/ml |
PROCESSING PARAMETERS
| Volume Mix Ratio | 1:1 |
| Processing Temperature | Min. 80℃ |
| Pressure | Min. 180 bar |
NOTE: StrataGemma PS 197C blend needs to be stirred well prior to use.
SUBSTRATE PREPARATIONS GENERAL RECOMMENDATIONS
Spray systems should only be applied to clean, dry and sound surfaces. Remove all dust, oil, grease, and lose rust, or any other foreign material to ensure adequate adhesion.
CONCRETE
Concrete substrates should be completely cured before coating or a minimum of 28 days must have passed. Laitance, release agents, and salts need to be removed by high-pressure water jetting or sandblasting. Other substrate cleaning guidelines can be consulted via SSPC-SP13, NACE 6. It is important to note that the use of a primer is generally needed to achieve adequate adhesion. The recoat window recommended by your supplier should also be respected.
METAL/STEEL
Metal surfaces need to be prepared by means of sandblasting until they have a nearly white appearance. The surface profile will ensure adequate mechanical adhesion. Solvent cleaning is needed to remove any oil and grease. If priming is needed, this should be undertaken within eight hours of sandblasting to prevent any flash rusting.
STORAGE
Containers of StrataGemma PS 197C should be stored indoors in a well-ventilated area under normal factory conditions at temperatures of between 20-25°C. Stored under recommended conditions, and in an unopened, sealed container.
SHELF-LIFE
StrataGemma PS 197C have a storage life of six months.
TECHNICAL SERVICE
- GCPL has an advisory service on concrete mix design & application of right products at right place, can be contacted if assistance is
- GCPL maintains a technical division with highly qualified Technical Personnel to investigate and advise on subjects related to concrete and the Construction
- The Division will advise on the correct use and selection of right products at the right
FOR YOUR PROTECTION
GEO Constech Pvt. Ltd. Polyurethanes warrants only that its products meet the specifications stated in the sales contract. Typical properties, where stated, are to be considered as representative of current production and should not be treated as specifications. While all the information presented in this document is believed to be reliable and to represent the best available data on these products.
NO GUARANTY, WARRANTY OR REPRESENTATION IS MADE. INTENDED OR IMPLIED AS TO THE CORRECTNESS OR SUFFICIENCY OF ANY INFORMATION OR AS TO THE MERCHANTABILITY OR SUITABILITY OR FITNESS OF ANY CHEMICAL COMPOUNDS OR OTHER PRODUCTS FOR ANY PARTICULAR USE OR PURPOSE OR THAT ANY CHEMICAL COMPOUNDS OR OTHER PRODUCTS OR THE USE THEREOF ARE NOT SUBJECT TO A CLAIM BY A THIRD PARTY FOR INFRINGEMENT OF ANY PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT. THE USER SHOULD CONDUCT A SUFFICIENT INVESTIGATION TO ESTABLISH THE SUITABILITY OF ANY PRODUCT FOR ITS INTENDED USE.
Liability of GEO Constech Pvt. Ltd. Polyurethanes for all claims, whether arising out of breach of contract, warranty, negligence, strict liability or otherwise is limited to the purchase price of the material. Products may be toxic and require special precautions in handling. For all products listed, the user should obtain detailed information on toxicity, together with proper shipping handling and storage procedures and comply with all applicable safety and environmental standards. Toxicity and risk characteristics of chemical compounds and other products may differ when used with other materials or in a manufacturing or other process. Those risk characteristics should be determined by the user and made known to handlers, processors and end users.
