fbpx

DrucStone Clear Epoxy Resin

Description

PRE-POLYMERISED HIGH STRENGTH, FREE-FLOWING GROUTING PRODUCT EPOXY RESIN

DRUCSTONE-155E clear epoxy resin is a low viscosity, free-flowing pre-polymer with high early strength which is suitable for repairing concrete blocks, asphalt, renderings, stone, asbestos, cement, wood, concrete, and mortar. It is high penetration allows filling the finest of cracks!

DRUCSTONE-155E can be applied in dry as well as damp conditions. It is a ready-to-use two-component EPOXY RESIN product with clear epoxy resin. Packs ‘A’ & ‘B’ of the product are pre-weighed and should be used in full quantity.

FEATURES of Epoxy Resin

  • Easy to apply either by conventional sprayers or by state-of-the-art pumps.
  • Outstanding resistance to water, weather, chemicals, shock, vibrations, and abrasions.
  • Excellent adhesion and shear strength.
  • Extremely reliable quality as DRUCSTONE-155E is produced under rigid quality control.
  • Compressive with substrate and topcoat.

USES of Clear Epoxy Resin

  • Bonding agent for micro-fine cracks, marbles, granite, and other stones.
  • Repairing structures such as Dams, Concrete, Water reservoirs, Canals, Tunnels, Over Bridges, Mines, and tanks.
  • Interiors and exteriors of buildings, concrete and mortar surfaces including industrial floors, metal surfaces, and wood.

APPLICATION

SURFACE PREPARATION

For coating purposes:

For coating of cement mortars and concrete, the product should be fully cured for at least 28 days at  25oC and 42 days old at 10 to 15oC. Before application, the surfaces must be sound, clean, and free from standing water. The surface may be slightly damp or dry. The surfaces must be totally free of contaminants such as chemicals,  dust, oil, or grease. Concrete, mortar, and stone surfaces must be thoroughly prepared to remove any surface laitance, dust, and friable material. Surfaces may be best prepared by sandblasting or etching with acid. For grouting purposes, we can use it directly in the boreholes and cracks.

MIXING

Mix all contents of Pack ‘A’ (Base) with all contents of Pack ‘B’ (Hardener) for 2 – 3 minutes until it is smooth. Mix well with spatula, drill, or paddle. Please ensure that only a little air is in the mix. Packs ‘A’ & ‘B’  are pre-weighed and should be used in full quantity.

CLEANING

 If the material is soft, use solvent for its removal. If it is hard, remove it mechanically.

TECHNICAL DATA

SL. NO.TESTING PARAMETERSOBSERVATIONSSTANDARDS
1.Mixing RatioPACK A : PACK B = 1:0.5
2.Service Temperature (oC)25-35
3.Relative Density (at 27oC ± 2oC)1.10 ± 0.02
4.Tack – Free Time (at 27oC ± 2oC)30 Minutes
5.Pot Life (at 27oC ± 2oC)15 MinutesASTM D-2471
6.Gel Time (at 27oC ± 2oC) Without Fillers20 ± 2 Minutes
7.Gel Time (at 27oC ± 2oC) With Fillers
8.Initial Cure (at 27oC ± 2oC)12 Hours
9.Full Cure (at 27oC ± 2oC)7 Days
10.Bond Strength at 27oC ± 2oC in 7days150 ± 10 (Kg / cm²)ASTM D-882
 

11.

Compressive Strength (Kg / cm²)

·         3 Days

·         7 days

·         350 ± 50

·         750 ± 50

 

ASTM D-695

12Tensile Strength (Kg / cm²)20 ± 2ASTM D-638
13.Chemical ResistanceExcellent resistance to range aggressive chemicals
14.Dust Proof ExtentGood
15.AppearanceSmooth, glossy, dense

surface with joint-less finish

HEALTH & SAFETY

This is a  highly in-flammable product.  Smoking or naked flame within  10 meters from the product is not advisable. Ensure proper ventilation or use a circulator in a confined area.

STORAGE & SHELF LIFE

 Store in a cool and dry place. Use within one year from the date of manufacturing.

PACKING

DRUGSTONE-155E is available in packs of 25 Kg and 50 Kg. Orders for bulk quantity shall be made on-demand.

Inquiry Form